BS EN 12079-1 PDF

This British Standard is the official English language version of. EN Together wi th BS EN i t supersedes. BS EN l which. BS EN BRITISH STANDARDOffshore containers and associated lifting sets — Part 1: Offshore containers — Design, manufacture. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European.

Author: Shakat Gogar
Country: Laos
Language: English (Spanish)
Genre: Photos
Published (Last): 6 September 2017
Pages: 37
PDF File Size: 6.52 Mb
ePub File Size: 16.94 Mb
ISBN: 836-8-65290-280-8
Downloads: 70504
Price: Free* [*Free Regsitration Required]
Uploader: Takasa

The impacting corner shall be the one expected to have the lowest rigidity.

However, the 112079-1 height difference between the highest and lowest point of the underside of the container corners need not be more than mm. The NDE operators shall issue reports describing the weld quality.

Aluminium alloys used in e containers shall be made by rolling or extruding. For tank containers, the actual distribution of the tare mass shall be used for the calculations. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.

BS EN 海岸集装箱及其相关提升设备 第1部分:海岸集装箱 设计丶制造和标记 – MBA智库文档

120779-1 2 It is recommended that pad-eyes be slotted into the primary structure NOTE 3 Where ISO-corner fittings are mounted in conjunction with pad eyes, the corner fittings are not intended for lifting with slings offshore. Non-alloy quality and special steels ENOpen die steel forgings for general 12079-11 purposes — Part 3: In addition to the requirements of 5.

B Test report 2. Additional requirements for offshore service containers In addition to the transport related requirements covered by EN and the regulations described above, offshore containers may be designed or equipped for special service tasks, e.

If the additional deck is removable, it will be necessary to carry out the test with the test load divided between the additional deck and the floor, as well as with the whole test load on the 1279-1.

  DYNAMICS OF YOGA SWAMI SATYANANDA SARASWATI PDF

Double doors shall have at least one such locking device on each door, locking directly to the top and bottom frame. Hinges shall be protected against damage from impact loads. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.

Only materials with non- wn properties shall be used. The number of containers to be tested shall be agreed in advance and is dependent on the total number in the production series.

NOTE Appropriate provision should be made to ensure that there is no risk to the health and safety of the inspector.

BS EN 12079-1:2006

RevisionsBritish Standards are updated by amendment or revision. However, to avoid misinterpretation additional marking shall be kept to a minimum. NOTE Guidance as to the recommended knowledge e experience of staff responsible for inspections for the purposes of schedule 7. NOTE The categories applicable to the structural members shall be agreed with the certifying body in each case.

NOTE 12079-11 Type testing may not replace design review, but may in certain cases be a partial substitute for strength calculations. Find 1279-1 Items This product falls into the following categories. NOTE 12079–1 For containers with special features where additional design requirements apply, suitable tests should be made to verify that those requirements are met. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or 120799-1 any CEN member.

NOTE 2 A matt black panel of appropriate size may be provided for the application of temporary information. The facility shall include a suitable means of lifting and supporting the container for the purposes of inspecting the underside.

It shall be held for 5 minutes before measurements are taken. Where containers are designed for stacking, and the lifting set hangs over the side of the bss frame they shall be fitted with a method of protection for those exposed parts, e. If a container is fitted with pockets that are only for empty handling, the container shall be marked according to 9.

Requirements for the lifting set and for non-transport related requirements, relating to offshore service containers, e. Plates shall be made of corrosion resistant material securely attached gs in a manner designed to avoid unauthorized or accidental removal. 120799-1 materials with non-ageing properties shall be used. Method of test at ambient temperature ENHot rolled products of structural steels – Part 1: The certificate shall be retained by the owner.

  LNG A NONTECHNICAL GUIDE TUSIANI PDF

You may find similar items within these categories by selecting from the choices below:. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. The container shall be suspended from a quick release hook. Double doors shall have at least one such locking device on each door, locking directly to the top and bottom frame.

For other primary structure, the use of fillet welds shall be justified by design appraisal including calculations and consideration of failure modes. NOTE 3 On closed dry cargo containers this will normally be at the door end. Users of British 1207-91 are responsible for their correct application. Pad eyes shall not protrude outside the boundaries of the container other than vertically upward, and shall as far as possible be designed to avoid damage from other containers.

Method of test at ambient temperature.

Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services.

NOTE Equipment permanently installed on a container is considered to be part of the container for certification purposes.

For dedicated purpose containers e. For specimens with their axis transverse to the final rolling direction the valve shall be two thirds of that for longitudinally orientated specimens. Please download Chrome or Firefox or view our browser tips. Test temperatures shall be as given in Table 1. NOTE Aluminium containers may need to be specially marked to warn of the danger of sparking see 5.