Add Attachments to Content Item ‘ASTM D Glass Transition Temperature ( DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) . ASTM D Glass Transition Temperature (DMA Tg) of Polymer ASTM D has become a widely used test standard in many companies due to. ASTM D用DMA测试Tg_能源/化工_工程科技_专业资料。Designation: D – 07?1 Standard Test Method for Glass Transition.

Author: Vonos Feran
Country: Honduras
Language: English (Spanish)
Genre: Technology
Published (Last): 4 June 2009
Pages: 344
PDF File Size: 16.94 Mb
ePub File Size: 3.67 Mb
ISBN: 810-2-32212-226-7
Downloads: 35051
Price: Free* [*Free Regsitration Required]
Uploader: Malamuro

Mount the specimen in dual cantilever mode or three-point bending mode. The temperature at which a signi? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For example, a linear plot scale will result in a lower value of DMA Tg. Historical Version s – view previous versions of standard.

The DMA Tg value is frequently used to indicate the upper use temperature of composite materials, as well as for quality control of composite materials.

ASTM E Summary of Test Method 4. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A non-standard DMA Tg de? The second tangent line Aetm B, Fig. Users of this standard are expressly advised that determination of the validity of any such patent rights, and asym risk of infringement of such rights, are entirely their own responsibility.

The same heating rate shall be used for all samples whose results are to be compared. The same conditions shall be used for both calibration and testing runs.

The conditioned specimens shall be tested within 30 minutes after removal from the conditioning chamber, or stored in sealed MIL-PRF or equivalent aluminized bag until test. NOTE 2—Guides EEand E contain data reporting recommendations for composite materials and composite materials mechanical testing.


For comparison purposes the peak temperature of the tangent delta curve Tt is identi? Weigh the specimen after the test to the nearest milligram 0. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D7028 – 07(2015)

Should the results be retained, axtm these conditions shall be described in the test report. Before the transition the storage modulus is relatively constant, the sigmoidal change during transition is clear, and after the transition the storage modulus is relatively constant. Weigh the specimen to the nearest milligram 0.

These values indicate that the material factors did not have a signi? Dynamic Mechanical Proper- ties: In general, for a given material, a higher sstm frequency produces a higher DMA Tg value than this standard, while use of the resonance mode will yield a different DMA Tg that may be either higher or lower than the standard. It is ideal because the glass transition is clearly displayed.

Before the transition the storage modulus continues to slope downward and after the transition the storage modulus continues to slope downward. Any deviations from the standard orientation shall be reported and the test results noted as non-standard.

Precision and Bias 4 The maximum time between cure lamination and testing shall be 30 days, after which, prior to testing, specimens shall be oven-dried in accordance with Your comments will receive d028 consideration at a meeting of the responsible technical committee, which you may attend.


If a non-standard frequency, or the resonance mode, is used, the non-standard approach shall be described in the report and the test result recorded as non-standard. Your comments are invited either for revision of asrm standard or for additional standards and should be addressed to ASTM International Headquarters. Examples are shown in this appendix to provide graphical illustrations of how to select the two tangent lines. During the glass transition, the storage modulus of the composite material is signi?

Generally, the specimen should be centered between the clamp faces and be parallel to the base of the instrument. If a different heating rate is used it shall d70288 described in the report and the d70028 recorded as nonstandard.

If you sstm that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. It is widely known that heat transfer limitations are more pronounced in DMA apparatus compared to other thermal analysis techniques, such as differential scanning calorimetry DSC and thermomechanical analysis TMA.

ASTM D用DMA测试Tg_百度文库

A change in heating rate will affect the glass transition temperature result; the standard heating rate is the best available compromise for comparing DMA Tg results of dry and wet laminates. If the testing is part of a designed experiment, other sampling techniques may be used if described in the test plan. D — 07? Depending on the analyzer, typical specimen size can range from 56 6 4 3 12 6 1 3 2.