ASTM B specification refers to Alloy 20 Flanges intended for corrosive high temperature service. A sufficient discard shall be made from each ingot to secure . ASTM B Direct No.: + Fax No.: + Email: [email protected] Board No.: + Website: . Buy ASTM B Standard Specification for Forged or Rolled UNS N, UNS N, UNS N, UNS N, UNS N, UNS N, UNS.
|Published (Last):||11 February 2004|
|PDF File Size:||18.48 Mb|
|ePub File Size:||6.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
Requirements for chemical and product check analyses and hydrostatic, macroetch, and tension tests are given.
NOTE 2—The recommended annealing temperatures all followed by water quenching or rapidly cooling by other means are: B — 04 Standard Speci? Link to Active This link will always route to the current Active version of the standard. The material shall have a asmt structure as shown by the macroetch test in 7.
Siddhagiri Metals and Tubes supplies an extensive range of flanges in all grades.
ASTM B Nickel Alloy 20 Pipe Flange Supplier · ASTM B UNS N
This abstract is a brief summary of the referenced standard. Workmanship, Finish, and Appearance 9. A number in parentheses indicates the year of last reapproval. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
ASTM B462 – Flange
A sufficient discard shall be made from each ingot to secure freedom from injurious piping and undue segregation. The values given in parentheses are for information only.
Originally approved in Looking for some more information? Requirements for forging done by hammering, pressing, rolling, extruding, or upsettinghot working, and heat treatment are detailed. ASTM A flange offer users a combination of nickel, chromium, molybdenum, and copper which provides good general corrosion resistance.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided b42 part of the standard. Your comments are invited either for revision of satm standard or for additional standards and should be addressed to ASTM International Headquarters. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
Work Item s – proposed revisions of this standard.
The material shall meet the requirements specified for the mechanical properties including tensile strength, yield strength, and elongation. The material shall meet the requirements specified for the mechanical properties including tensile strength, yield strength, and elongation. If you feel that your comments have zstm received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Aastm Properties and Other Requirements 7. Offer on Fasteners Sitemap. Materials and Manufacture 5. When this supplementary requirement is speci? Siddhagiri Metals and Tubes Rating: Flanges supplied by us are industry standard approved and certified. Few of the major brands we represent are Nippon, Sumitomo, Outokumpu, Sandvik etc.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Rejection and Rehearing In such cases, the question of acceptable and unacceptable character of metal? However, the manufacturer of such forgings is responsible as required in accordance with The product of UNS N shall be furnished in the annealed condition.
When it is impractical to provide forgings for test purposes, test bars may be made from the billet or bar, provided they are given approximately the same reduction and heat treatment as the forgings.
In case of dissatisfaction with the results of the test, the producer or supplier may make claim for a rehearing. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Alloy 20 flanges are best suited for mid-range corrosion use better than steel alloys.
The material shall conform to the chemical composition prescribed for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, copper, columbium, tantalum, nitrogen, iron, cobalt, tungsten, vanadium, titanium, zirconium, aluminum, yttrium, and cerium. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Examples of such requirements include, but are not limited to, the following: A sufficient discard shall be made from each ingot to secure freedom from injurious piping and undue segregation.
This examination is a method to assure that no material grade mix-up has happened during manufacturing and marking of the product.
The material shall conform to the chemical composition prescribed for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, copper, columbium, n462, nitrogen, iron, cobalt, tungsten, vanadium, titanium, zirconium, aluminum, yttrium, and cerium.
Historical Version s – view previous versions of standard.
Last previous edition approved in as B — NOTE 1—A typical ordering description is as follows: Forgings ordered under these speci?
If Practice B is speci?