ASTM B153 PDF

B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering

Author: Kagore Teshura
Country: India
Language: English (Spanish)
Genre: Science
Published (Last): 27 December 2017
Pages: 133
PDF File Size: 15.48 Mb
ePub File Size: 8.5 Mb
ISBN: 683-7-19472-680-7
Downloads: 99729
Price: Free* [*Free Regsitration Required]
Uploader: Mura

By using this site, you agree to the Terms of Use and Privacy Policy. Standard Specification for Nickel Oxide Sinter.

ASTM B Specifications List – Colorado-Metallurgical-Services

Mercurous Nitrate Test Standard Specification for Ferromolybdenum. If reexamined or retested, tubes with signals that are found to have been caused by minor mechanical damage, soil, or moisture, shall not be cause for rejection of the tubes provided the tube dimensions are still within prescribed limits and the tube is suitable for its intended application.

Standard Tube Size, inch Up to and including 3? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Standard Specification for Ferrochromium.

All defective items shall be replaced with acceptable items before lot acceptance. The purchaser shall have the right to perform ast of the inspections or tests set forth when such inspections and tests are deemed necessary to assure that the material conforms to prescribed requirements.

Rockwell hardness shall be made on the inside surface of the tube.

Immediately after removal from the solution, the specimen shall be wiped free of excess mercury and examined for cracks. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Preparation for Delivery S4. However, if subsequent testing by the purchaser establishes that the material does not meet these requirements, the material shall be subject to rejection.

  AR 672-5-1 PDF

List of ASTM International standards – Wikipedia

Screening and resubmittal of samples from rejected lots for visual and dimensional examination is acceptable. C Rockwell hardness values shall apply only to tubes having b53 wall thickness of 0. Rectangular including square tubes shall normally be supplied only in drawn general-purpose temper. Current edition approved Oct.

For all other tube no Rockwell hardness values shall apply.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory b15 prior to use. This list may include either current or withdrawn standards. Limits for unnamed elements are to be established by agreement between manufacturer or supplier and purchaser. Ten alloys are speci? A Alloy Designations of Speci? C on tube sizes greater than 5 in.

Tension tests are required for tubes with a wall thickness under 0. Standard designations usually consist of a letter prefix b13 a sequentially assigned number. A withdrawn standard has been discontinued by its sponsoring committee. The test method used shall provide for easy visual detection of any leakage, such as by immersion of the tube under water or by the pressure differential method.

Originally published as B — 40 T.

ASTM B153 – 11(2017)

Wear rubber gloves when conducting the test. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Zstm Specification for Steel Screw Spikes. This page was last edited on 30 Novemberat When there is a need for light-drawn b513 hard-drawn tempers these are to be supplied as agreed upon between the manufacturer and the purchaser.

  KALEIDOSKOP 7TH EDITION PDF

Sampling for Visual and Dimensional Examination Standard Specification for Steel Track Spikes.

List of ASTM International standards

Standard Specification for Gray Iron Castings. Standard Specification for Ferromanganese. Hard-drawn temper is used only where there is need for a tube as strong as is commercially feasible for the sizes indicated.

Former soft anneal soft anneal light anneal light anneal soft anneal soft anneal light anneal light anneal soft anneal soft anneal up to 0. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Standard Specification for Pearlitic Malleable Iron. Standard Specification for Silicomanganese.

Alternatively, if the manufacturer uses speed-insensitive eddy-current units that are equipped so that a fraction of the maximum unbalance signal is able to be selected, the following percent maximum unbalance signals shall be used. A standard may be withdrawn with or without replacement.

This may optionally be followed by a dash and the last two digits of the year in which the standard was adopted. Incomplete lists from February Last previous edition B — When agreement on the Rockwell hardness tests cannot be reached, the tensile strength requirements of Table 2 shall be the basis for acceptance or rejection. Any evidence of leakage shall be cause for rejection.