Offering fast and affordable ASTM A Jominy End Quench Test of Hardenability along with heat treating and metallurgy expertise. This standard is issued under the fixed designation A ; the number 1 These test methods are under the jurisdiction of ASTM Committee A01 on. Steel. ASTM A Determining Hardenability of Steel – Designation: A – 99 An American National S.
|Published (Last):||12 August 2004|
|PDF File Size:||7.54 Mb|
|ePub File Size:||12.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
If the document is revised or amended, you will be notified by email.
Need more than one copy? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Proceed to Checkout Continue Shopping. The test specimen shall be 1. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. These smaller 19 specimens shall be tested in accordance with 5 of the method except that modi? It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench.
The sheath shall preferably be made from a plain low-carbon steel.
A — 99 Determinin Plating and Coating Testing. Place a aa255 of graphite or carbon, or a layer of carbonaceous material such as charcoal, in the bottom of the tube to prevent scaling.
Link to Active This link will always route to the current Active version of the standard.
The support for the specimen shall be dry at the beginning of each test. A lowpower measuring microscope is suitable for use in determining the distance from the quenched end to the center of the?
For readings to 8? The accuracy of this test method and the techniques used to develop it have been documented. For the example in Metal Progress, VolNo. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Aetm make Rockwell hardness measurements on the C scale on the specimen as prescribed in 6. An anvil providing a means of very accurately measuring the distance from the quenched end is essential. The small test specimen inserted in the sheath, and the sheath warmed to a temperature above the melting point of a25 Woods metal.
This standard is also available to be included in Standards Subscriptions. A facsimile of the standard ASTM hardenability chart3 on which typical hardenability curves have been plotted is shown in Fig.
ASTM A – The Jominy End Quench Test of Hardenability
Cast tests need not be normalized. The positioning of the indenter should be checked with sufficient frequency to provide assurance that accuracy requirements are being met. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
The variations between spacings should be even smaller. This test method assures that the material you are using is going to respond correctly to heat treatment. It astk the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Link to Active This link will always route to the current Active version of the standard. Tempering of the normalized sample to improve machinability is permitted. A satisfactory type of support for the standard 1. The test consists of a255 quenching one end of a cylindrical test specimen 1.
ASTM A – 10 Standard Test Methods for Determining Hardenability of Steel
The two test methods include the quantitative end-quench or Jominy Test and a method for calculating the hardenability of steel s255 the chemical composition based on the original work by M. The two test methods include the quantitative end-quench or Jominy Test and a method for calculating the hardenability of steel from the chemical composition based on the original work by M.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Distances for the odd number 1? It is important that no vertical movement be allowed when the major load is applied. The Certified Material Test Report shall state the method of hardenability determination. In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to a given hardness level.
ASTM A255 Jominy Hardenability Testing
Wilson Hardness Conversion Chart. We have no amendments or corrections for this standard. After sample is machined, it is normalized even if your material is already in the normalized condition running this will make sure it is in the normalized condition at specified a2555 and oven cooled.
Wash the sample in hot water.
The mold may also be used to form a 1. Active view current version of standard. The anvil must be constructed to move astj test specimen past the penetrator in accurate steps of 1? The use of these equations to plot curves may result in random in? Grossman and provides increased accuracy by re?