View and Download AMMCO installation instructions manual online. Disc Rotor Lathe. Lathe pdf manual download. iv • AMMCO Brake Lathes. Safety. Safety Notices and. Decals. For your safety, and the safety of others, read and understand all of the safety notices and . Get AMMCO Disc Rotor Lathe Manual. Get all AMMCO manuals!.

Author: Dakazahn Malakinos
Country: Dominica
Language: English (Spanish)
Genre: Love
Published (Last): 18 October 2009
Pages: 490
PDF File Size: 7.36 Mb
ePub File Size: 7.81 Mb
ISBN: 429-1-37800-384-7
Downloads: 78190
Price: Free* [*Free Regsitration Required]
Uploader: Vogrel

Now engage the automatic cross feed by moving the knobFig. When the cross feed has moved the cutting tools all the way across the face of the rotor, the feed will shut off automatically. If any of the goods called for on this bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods.

Tell us about it. Brake Lathes Cross Feed – The cross feed draws the twin tool bits across the face of a brake rotor when the cross feed drive is engaged. Chips and dust could be driven between machined parts and into bearings causing undue wear. Keep all guards, shields, and covers in place and in working order.

Feed Speed – Feed speed refers to the number of thousandths of an inch the cutting tools move across the face of the rotor per revolution of the spindle. Turn both tool bit controls to the desired depth-of-cut and lock them in position. Repeat the procedure for the other tool-bit holder.

Use the outer pulley groove for all passenger car and light truck rotors, Fig. Identify the hazard levels used in this manual with the following definitions and signal words: The patented self-aligning spacer prevents diagonal thrust on the adapters. Page 4 Safety Safety Notices and Decals For your safety, and the safety of others, read and understand all of the safety notices and decals included here and on the unit. B 10, and adjust the twin cutter so xmmco the rotor is centered between the tool bits.


Failure to follow safety instructions could result in personal injury to operator or bystanders and damage to the lathe or personal property. Make sure that the tool bits clear the rotor faces and the silencer band.



Don’t see a manual you are looking for? Your manual failed to upload Unplug unit from power source before servicing or adjusting. Brake Lathes Machining 8. Either rough or finish cuts may be taken to resurface a rotor. The cross also be operated manually using the cross feed handwheel. Comments to this Manuals Your Name.

Page 14 Brake Ammfo 4. Use a face shield and dust mask during dusty operations. Choose one of the inner grooves when machining medium duty truck rotors.

AMMCO 7000 Hustler Disc Brake Lathe Operation Manual

The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice. Page 14 Turn the left hand tool bit control until the tool bit contacts the rotor surface and makes a scratch cut no deeper than. Every hours drain the oil and refill to the dipstick level with clean EP gear oil. Reconditioning Disc Brake Rotors The patented self-aligning spacer prevents diagonal thrust on the adapters. Any excessive wear or deformity should be noted and, if not within acceptable limits, the rotor should be replaced.


KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference by supervisors and operators. Oiling The lathe is shipped from the factory with the correct 70000 and type of oil. Got it, continue to print. Brake Lathes The scratch will usually appear as an incomplete circle.

AMMCO 7000 Disc Rotor Lathe User Manual

To print the manual completely, please, download it. Also always wear safety glasses or a face shield. Table Of Contents Cleaning DO NOT throw them into a box. Also review the following general safety instructions. Use a micrometer to check the thickness of the rotor at no less than three points around the circumference about 1″ Clean, repair, remount, or replace as necessary.

Reconditioning Disc Brake Rotors-set-up Fig. Turn the cross feed handwheel clockwise until the tool bits are near the rotor hub, Fig. Refill as necessary with EP gear oil and check the oil level often. Move the belt to the pulley groove that will give the correct spindle speed for the cut to be taken, Fig. Spindle Speed – Release the belt tension by moving mamco V-belt adjusting lever clockwise, Fig.

Center the twin cutter to the rotor. Maintain unit properly, keep work surfaces and work area clean. By pressing ‘print’ button you will print only current am,co.