Ademco XM/First Alert FAC Program Sheet. Enter Program 1. + 8 + 0 + 0 (Display should show 00). or. 2. Power down then back up and press. The Ademco XM is a UL Listed commercial fire and burglary control system. Its advanced integrated design is aimed at providing a powerful solution for the. ADDENDUM TO: INSTALLATION INSTRUCTIONS FOR XM CONTROL Ademco High Speed off-normal test reports use channel 3 =1 and status channel .

Author: Fenririsar Yomi
Country: Dominica
Language: English (Spanish)
Genre: Technology
Published (Last): 1 February 2006
Pages: 304
PDF File Size: 15.80 Mb
ePub File Size: 13.25 Mb
ISBN: 855-8-62584-778-5
Downloads: 86204
Price: Free* [*Free Regsitration Required]
Uploader: Shatilar

KP -zone – and polling loop – are all common. Select a valid country. As noted above, the panel mounting screws provide an electrical path between the earth ground terminal 30 and ademcco panel cabinet.


If using dip-switch RPMs, check all the dip-switches. The maximum number of modules which can be configured as shown in Figure 1 is limited to no more than 8, adwmco by the need ade,co a DC power supply to furnish 50ma 12 Vdc plus the polling loop output current per module. Seller’s obligation is limited to repairing. With this field enabled, no other polling loop devices will operate. Representative APR variable It’s a community-based project which helps to repair anything.

Seller information ecomelectronics Please enter a number less than or equal to 1, Determine the maximum device loading on the polling loop branch by adding the load currents per device determined from Table 2. Lay the PCB on a non conductive material wood or cardboard. When a short occurs on a polling loop branch, it illuminates a trouble LED and isolates the defective branch from the avemco reducing troubleshooting time.



The maximum avemco of V-plex device loading that can be placed on one or more polling loops with a single supporting control panel is mA.

Processed by PayPal Get more time to pay.

Add to Watch list Watching Watch list is full. The panel recognizes a short when the voltage on the polling loop drops to 4. What does this price mean? Verify that there are no ECP devices enabled in programming, that do not exist.

Ademco VISTA 5140XM User Manual

Seller assumes all responsibility for this listing. Add to watch list. Isolate different branches of the polling loop to isolate the problematic device. For additional information, see the Global Shipping Programme terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other 5140x.

Vista security system installation and setup guide pages. See other items More Failure to follow these rules will cause problems on these zones as well as other polling loop zones. Zones will not adeco 1. The FAc and FAc and up do not. When programmed, receive messages on their display screens seconds display In addition, the sum of the wire lengths of both the input and output of a 510xm is also limited to 12, ft.

Please enter a valid postcode. This item will be shipped through the Global Shipping Program and includes international tracking. There are no base tampers on our V-plex smoke detectors.

The next step is to remove the panel from the cabinet.


However, if you remove the earth ground wire, your panel may still have a connection to earth ground through the cabinet and conduit connected. This cannot be disabled by a dip-switch like the sd.

Locate the row in the table selected in step 1 corresponding to the total device load current determined in step 2. This amount is subject to change until you make payment. There may be more than one wire with a problem. If you have voltage below 7 volts, confirm load current draw and wire limits on adekco loop is within specs.

Does grounding the metal can affect ground fault?

ADEMCO 5140XM User Manual

Back to home page. For any other zone types, proceed to the next step. You may overlap these with wireless zones. Please enter up to 7 characters for the postcode.

Verify that all devices are correctly wired. See the seller’s listing for full details. As a last resort, bring the devices back to the control panel to see if they work alone at the panel. Isolate individual devices until you have a basic subsystem that works properly.

To assist trouble shooting, be sure that Polling Loop Short detection zone 97 or and Earth Ground fault detection zone 72 or are enabled, Earth Ground fault detection is only a feature of a commercial fire panel.

Read more about the condition.