61F-GPN2 AC from OMRON >> Specification: Liquid Level Controller, 61F- GP-N2 Series, Conductive, Vac, W, 80 ms. Find great deals for Omron 61F-GP-N2 Processor/Controller. Shop with confidence on eBay!. The 61F-GP-N2-AC is a Conductive Level Controller for automatic water supply and drainage control. Compact plug-in controller for single or two-point.

Author: Arashigul Mazurr
Country: Serbia
Language: English (Spanish)
Genre: Travel
Published (Last): 12 June 2017
Pages: 187
PDF File Size: 7.95 Mb
ePub File Size: 9.38 Mb
ISBN: 986-9-14343-385-9
Downloads: 19398
Price: Free* [*Free Regsitration Required]
Uploader: Tojataur

The water provides a current between the earth probe and the high-level probe. If this differential is not required, the low-level probe need not be connected. In this case the relay does not de-energize until the water level falls below the low-level probe.

Spin a lock nut and a spring washer onto the electrode. Omron disclaims all other warranties, express or implied. Usually, electrodes are used in a set of three: When resistance to high pressure is required. The diagram shows the connections for water supply. Avoid use of the separators omro dust-containing liquids. The output relay in the controller 61f-ggp-n2 energized when the water level reaches the high-level probe and de-energized when the water level falls below it.

When using a noise filter, check the voltage and current and install it as close to the product as possible. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

However, a type having 1, mm length electrodes is available on request. Using the low-level probe allows a wide differential between switching a pump on and off, and can avoid excessive pump operation during tank emptying or filling. Documents Flashcards Grammar checker. Doing so causes malfunctions such as chattering, etc. In the interest of product improvement, specifications are subject to change without notice.


When the required length of the electrode is more than 1 m, use a separator at each joint of two electrodes so as to prevent the electrodes from contacting one another. Similarly, avoid using next to a high-capacity contactor which may impacts at operation. All units are in millimeters unless otherwise indicated. When taping one of the electrodes to prevent it from contacting the other electrodes in water, do not tape the electrode entirely but leave at least mm of its end uncovered.

Return of any Products by Buyer must be approved in writing by Omron before shipment.

Limitation on Liability; Etc. Make sure that the terminal cover is installed before using the product. To convert grams into ounces, multiply by 0.

Omron 61F-GP-N2 Processor/Controller | eBay

This is a temporal bone which had an implant electrode To convert millimeters into inches, multiply by 0. Standard electrodes are made of stainless steel and usable in purified water, sea water, sewage, acid except acetic acid, sulfuric acid, etc.

It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. Easy-to-replace separate versions facilitate maintenance of electrodes. Indication of liquid buildup due to filter blockages. If the screws are not tight, DIN rail ssocket sthe product and cable s may lead to come off.

Doing so can reduce some effects of noise. E1 Electrodes are in actual contact with the liquid.

When draining, change the connection Tb to Ta. Data presented in Omron Company websites, catalogs and other materials is omgon as a guide for the user in determining suitability and does not constitute a warranty. Ideal for use in tanks where temperature or pressure inside the tank is high, e.


61F-GP-N2 – OMRON Industrial Automation

For acids, alkalis and sea water, electrode holders may be as much as 1 meter apart to operate properly. Between electrode E2 and E3 Response time Operate: For low specific liquids. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments.

Doing so causes malfunctions by getting vulnerable to induction noise.

Omron 61F-GP-N2 Processor/Controller

The earth terminal must be grounded. Use separator when connecting. For two-point control a low-level probe is used as well. After fixation, osmium staining, and dissection the Buyer shall take application responsibility in all cases.

Connect the short electrode to E1, the medium electrode to E2, and the long electrode to E3. A low voltage is applied between these probes and the earth probe or tank, if it is electrically conductive. Electrochem review part 1 Consider the following two reactions: In sewage use, electrode holders must be installed 10 to 20 cm apart from one another.

Ideal for soft drink vendors, etc. Secure the connecting nut by tightening the lock nut and spring washer.

When in doubt, special part numbers may be assigned to fix or establish key specifications for your application.