YZF(Z). Il convient de lire attentivement ce manuel avant la première utilisation du véhicule. Read this manual carefully before operating this vehicle. Yamaha YZF REPAIR SERVICE MANUAL CD. $ Buy It Now. BONUS – Owners manual included in each. To provide our customers with the best after sales service, your feedback is appreciated. To contact: Yamaha Motor Australia, click here. Yamaha Motor New .

Author: Misar Vosho
Country: Ghana
Language: English (Spanish)
Genre: Environment
Published (Last): 25 December 2004
Pages: 13
PDF File Size: 8.69 Mb
ePub File Size: 10.28 Mb
ISBN: 725-1-55423-131-2
Downloads: 15435
Price: Free* [*Free Regsitration Required]
Uploader: Nigor

Brake caliper piston dust seal Refer to removal section. Hot starter cable Aligh the paint mark on the cylin- Radiator hose 1 Fit the timing chain “3” onto both 5.

Yamaha YZF – Owner’s Manual – Pages – PDF

Radiator guard Radiator hose clamp Only loosening. Timing chain tensioner Refer to removal section.

Don’t show me this message again. Clutch boss Refer to removal section. Skip to main content. Nut front wheel axle Front wheel axle Front wheel Continue push- ing the engine stop switch till the en- gine comes to a stop.


Turn the handlebar lock to lock. Cap bolt ring wrench: Perform the pre-operation checks on the machine. Crankshaft end accessing screw Refer to removal section. Nut rear wheel axle Rear wheel axle Drive chain puller Rear ownera Refer to removal section. Do not strike the inner race of the Nm Drain the brake fluid. Clutch lever holder Engine stop switch Brake master cylinder Refer to removal section.


Yamaha YZ250F Manuals

Nut primary drive gear Refer to removal section. Disconnect the CDI magneto lead. Hot starter cable Disconnect at the lever side. It is necessary to set the carburetor while checking the operating conditions of the engine. This manual contains all the comprehensive information required to handle anything from minor repairs to major overhauls or tear downs of your Yamaha motorcycle.

Radiator cap tester adapter YU, Steering nut wrench This tool is used when tighten the YU, steering ring nut to specification.

This type of main jet is pending on atmospheric zy250f. This model is not spill any gasoline on the the culmination of Yamaha’s vast ex- engine or exhaust system. Bearing Refer to removal section.

Radiator breather hose Fasten the throttle position sen- Radiator hose 2 Warp limit 0. Install the brake hose so that its Install the brake hose so that its pipe portion directs as shown pipe portion directs as shown and lightly touches the projec- and lightly touches the projec Carburetor overflow hose front end of the hose guide.

Fuel hose der head breather hose with the Connector cover Owners Service manual for Reproduction with transparent protective cover. Bolt axle holder Only loosening.

Fuel cock Hot starter lever Main axle Refer to removal section.

  AFI 11-409 PDF

Loosen the pad pin “3”. Oil ring end lower 3. Inner tube bending limit: Table of Contents Add to my manuals Add. Also shop in Also shop in. Cable guide Pass the throttle cables through Brake hose the cable guide.

Remove the crankcase bolts “1”, the crankshaft. Pass the carburetor breater hos- es so that they are not pinched between the upper engine bracket and carburetor. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Free local Las Vegas pickup. Blow out all passages and changing the throttle position sen- jets with compressed air. Check the steering stem by turn- ing it lock to lock. Brake caliper piston seal Refer to removal section. Clutch holding tool This tool is used to hold the clutch YM, when removing or installing the Cylinder head breather hose Insert the end of the fuel tank Pass the cylinder head breather Bear in mind that such factors as weather, terrain, geographical location, and individual usage will alter the required maintenance and lubrication intervals.

Drive chain Throttle grip